PerformanceTrucks.net Forums
Contacts in connector corroded... Badly
Contacts in connector corroded... Badly
0 2016/09/05 16:13:39
New socket in and installed
New socket in and installed
0 2016/09/05 16:13:42
Left signal lens had about half a cup of water in it...
Left signal lens had about half a cup of water in it...
0 2016/09/05 16:13:47
Right lens is dry
Right lens is dry
0 2016/09/05 16:13:53
Coils loosley mounted...
Coils loosley mounted...
0 2016/09/07 20:16:11
Only had three orphaned bellhousing bolts at moment, going to pull rest off the 5.3 once its out, and i need to pull a few other things as well...
Only had three orphaned bellhousing bolts at moment, going to pull rest off the 5.3 once its out, and i need to pull a few other things as well...
0 2016/09/07 20:16:14
0 2016/09/08 10:47:21
Tightened all the little stuff down, routed the harness, installed cooler lines, engine mounts, and ran new vent lines for the transfer case and trans.... Need one of the clips for the vent tubes an oil pressure sensor and possibly a starter i had to order one of the retainers for the trans cooler lines at the bottom of the bellhousing and a couple of odds and end bolts....
Tightened all the little stuff down, routed the harness, installed cooler lines, engine mounts, and ran new vent lines for the transfer case and trans.... Need one of the clips for the vent tubes an oil pressure sensor and possibly a starter i had to order one of the retainers for the trans cooler lines at the bottom of the bellhousing and a couple of odds and end bolts....
0 2016/09/08 17:53:27
0 2016/09/08 17:53:39
Transfer case out, most of harness disconnected
Transfer case out, most of harness disconnected
0 2016/09/09 18:28:52
This is howni left it thsi evening, another 45 minutes to an hour and the 5.3/4l60 wouldve been on the ground... Had a few snags along the way.....
This is howni left it thsi evening, another 45 minutes to an hour and the 5.3/4l60 wouldve been on the ground... Had a few snags along the way.....
0 2016/09/09 18:28:56
Sliced my finger pretty good on one of the speed nuts that hold the fascia on...
Sliced my finger pretty good on one of the speed nuts that hold the fascia on...
0 2016/09/09 18:31:49
Old engine and trans out and on the floor at 9:41am ...
Old engine and trans out and on the floor at 9:41am ...
0 2016/09/10 17:02:47
0 2016/09/10 17:02:51
New engine in and bolted down at 12:15, spent almost the entire time between removal and installation, figuring out the harness i need to build and the connector that isnt available, and transferring ac compressor, water pump and ground strap.... And manuevering the engine and trans through the shop to the truck.....
New engine in and bolted down at 12:15, spent almost the entire time between removal and installation, figuring out the harness i need to build and the connector that isnt available, and transferring ac compressor, water pump and ground strap.... And manuevering the engine and trans through the shop to the truck.....
0 2016/09/10 17:02:54
By 1:30 had t case driveshaft trans cross member etc all bolted in and buttoned up
By 1:30 had t case driveshaft trans cross member etc all bolted in and buttoned up
0 2016/09/10 17:02:57
Y pipe clearance..... The level check plug is a little more directly over the pipe than i like....
Y pipe clearance..... The level check plug is a little more directly over the pipe than i like....
0 2016/09/10 17:03:02
0 2016/09/10 17:03:26
0 2016/09/10 17:03:29
Really generic picture but gives you the idea
Really generic picture but gives you the idea
0 2016/09/12 22:49:08
0 2016/09/15 15:29:26
0 2016/09/15 15:29:33
0 2016/09/15 15:29:37
0 2016/09/15 15:29:46
This picture sucks, but both of the bolts are out... On both sides!!
This picture sucks, but both of the bolts are out... On both sides!!
0 2016/09/16 19:47:31
All 4 of the fascia to fender bolts broke, along with the speed nut on the left side lower fascia to bumper bracket....
All 4 of the fascia to fender bolts broke, along with the speed nut on the left side lower fascia to bumper bracket....
0 2016/09/16 19:47:37
And the mechanical portion of the swap is done....
And the mechanical portion of the swap is done....
0 2016/09/16 19:47:43
Pic sucks, but bolts are out, a little heat and a stud extra tor and the came right out through the inner wall of the fender....
Pic sucks, but bolts are out, a little heat and a stud extra tor and the came right out through the inner wall of the fender....
0 2016/09/16 20:09:33
All 4 of the fascia to fender bolts broke coming off along with the speed nuts on the lower fascia brackets..
All 4 of the fascia to fender bolts broke coming off along with the speed nuts on the lower fascia brackets..
0 2016/09/16 20:09:38
And she is officially back together, aside from a couple odd and ends....
And she is officially back together, aside from a couple odd and ends....
0 2016/09/16 20:09:45
Id check to see if theres any corrosion in the x109 connector....
Id check to see if theres any corrosion in the x109 connector....
0 2016/09/25 17:56:42
0 2016/09/25 20:07:07
0 2016/09/26 20:55:54
0 2016/09/30 14:24:39
This was my 99.... Which went from an engine swap to every mod i could do... Lol
This was my 99.... Which went from an engine swap to every mod i could do... Lol
0 2016/09/30 14:24:43
This was the yukon....
This was the yukon....
0 2016/09/30 14:27:03
0 2016/10/03 21:19:26
0 2016/10/05 19:16:08
0 2016/10/05 19:16:09
So am much as i dislike the mechanical side of the 2014 and up trucks i found one that may make me get one.... Realtree edition!!! However until i get some other stuff taken care of that isnt going to happen.... So in the meantime i had the guy that does all the graphics at work make a set similar to the door graphics but in a slightly different realtree pattern...
So am much as i dislike the mechanical side of the 2014 and up trucks i found one that may make me get one.... Realtree edition!!! However until i get some other stuff taken care of that isnt going to happen.... So in the meantime i had the guy that does all the graphics at work make a set similar to the door graphics but in a slightly different realtree pattern...
0 2016/10/06 20:42:29