PerformanceTrucks.net Forums
My makeshift frane mount....:dewey: :redneck:
My makeshift frane mount....:dewey: :redneck:
0 2016/06/23 20:03:07
New blocks, u bolts and add a leafs in place... And i lost a damn shock nut:sigh:
New blocks, u bolts and add a leafs in place... And i lost a damn shock nut:sigh:
0 2016/06/23 20:10:15
This started out as a temporary fix to hold the bars while i got everything together at the axle, and tightened it all up....
This started out as a temporary fix to hold the bars while i got everything together at the axle, and tightened it all up....
0 2016/06/23 20:10:24
0 2016/06/23 20:10:31
Bars in, and about same angle as driveshaft...granted the truck was on a lift, but...
Bars in, and about same angle as driveshaft...granted the truck was on a lift, but...
0 2016/06/23 20:10:39
Valve body/tcm removed.... Screwed me up for a minute it had 10mm head bolts where the 10epc torx were supposed to be....
Valve body/tcm removed.... Screwed me up for a minute it had 10mm head bolts where the 10epc torx were supposed to be....
0 2016/06/28 16:29:35
Vette bellhousing/pump ready to come off
Vette bellhousing/pump ready to come off
0 2016/06/28 16:29:41
Trash in pan....
Trash in pan....
0 2016/06/28 16:29:46
Pump face not too bad... Looks worse than it was...
Pump face not too bad... Looks worse than it was...
0 2016/06/28 16:29:53
The bellhousing side was worse than the pic shows.....
The bellhousing side was worse than the pic shows.....
0 2016/06/28 16:30:00
1-2-3-4 clutches burnt fairly well....
1-2-3-4 clutches burnt fairly well....
0 2016/06/28 16:30:07
3-5-r was TOAST!!!!! Hardly any material left on the frictions.... Could see the crack in the drum, no air check needed!!!
3-5-r was TOAST!!!!! Hardly any material left on the frictions.... Could see the crack in the drum, no air check needed!!!
0 2016/06/28 16:30:14
Slight bowing of the 3-5-r clutches!!!
Slight bowing of the 3-5-r clutches!!!
0 2016/06/28 16:30:21
0 2016/06/28 16:37:41
Snap ring from hell!!!!
Snap ring from hell!!!!
0 2016/06/28 16:37:53
Think these are 4-5-6 clutches...
Think these are 4-5-6 clutches...
0 2016/06/28 16:39:18
Center support which is also the 2-6 and low/reverse clutch housing...
Center support which is also the 2-6 and low/reverse clutch housing...
0 2016/06/28 16:44:00
The output planetary assembly
The output planetary assembly
0 2016/06/28 16:44:28
Output ring gear... All teeth intact!!
Output ring gear... All teeth intact!!
0 2016/06/28 16:44:43
4-5-6 hub came apart and the splines are chewed up from the stripped 4-5-6 clutches
4-5-6 hub came apart and the splines are chewed up from the stripped 4-5-6 clutches
0 2016/06/28 16:47:53
More of the 4-5-6 clutches
More of the 4-5-6 clutches
0 2016/06/28 16:48:21
2-6 clutches dont look too bad
2-6 clutches dont look too bad
0 2016/06/28 16:48:27
Likewise with the low/reverse
Likewise with the low/reverse
0 2016/06/28 16:48:33
No chewed up teeth on the planetary
No chewed up teeth on the planetary
0 2016/06/28 16:48:37
Everything going back in temporarily without clutches and sn output shaft
Everything going back in temporarily without clutches and sn output shaft
0 2016/06/28 16:48:41
Cebter support back in
Cebter support back in
0 2016/06/28 16:48:46
Went ahead and set the new 3-5-r in with the clutches.... The vise grips are the 1-2-3-4/3-5-r instaayion band tool!!
Went ahead and set the new 3-5-r in with the clutches.... The vise grips are the 1-2-3-4/3-5-r instaayion band tool!!
0 2016/06/28 16:48:52
Ls bellhousing in place
Ls bellhousing in place
0 2016/06/28 16:48:57
Valve body mounting....
Valve body mounting....
0 2016/06/28 16:49:04
Not completely black, but the face of the wheels are..... I miss the truck being pewter... Lol!!!
Not completely black, but the face of the wheels are..... I miss the truck being pewter... Lol!!!
0 2016/06/29 09:31:41
They are huge though!!!
They are huge though!!!
0 2016/06/29 10:57:10
New output shaft assembly, which is according to the paper in the box an updated design, the old one the ring gears were seperatable, these are built into the housing.....
New output shaft assembly, which is according to the paper in the box an updated design, the old one the ring gears were seperatable, these are built into the housing.....
0 2016/07/01 14:43:56
Solid ring gears
Solid ring gears
0 2016/07/01 14:43:59
Output came with new input/output shaft sensor harness
Output came with new input/output shaft sensor harness
0 2016/07/01 14:44:02
0 2016/07/02 09:52:02
0 2016/07/02 09:52:09
Theisbis the kent moore gm tool
Theisbis the kent moore gm tool
0 2016/07/02 12:34:53
This is an aftermarket version that you can see the lip if you look close enough
This is an aftermarket version that you can see the lip if you look close enough
0 2016/07/02 12:34:54
Thsi is how it should look, all in one piece!!!
Thsi is how it should look, all in one piece!!!
0 2016/07/06 17:50:12
0 2016/07/06 17:50:15