PerformanceTrucks.net Forums
0 2016/06/04 22:23:14
Shiny and black!!! They came with usual new center pins and the plastic dampeners to go in the ends...
Shiny and black!!! They came with usual new center pins and the plastic dampeners to go in the ends...
0 2016/06/06 17:34:04
Time to say goodbye to one of the tires that hit a point and wont wear out....
Time to say goodbye to one of the tires that hit a point and wont wear out....
0 2016/06/07 18:50:20
These tires were like this for at leat 2 years before i pulled the truck off the road..... They got here and stopped wearing.... Guess i shoukdnt complain but so much ive gotten, 7 or 8 years out of them!!!
These tires were like this for at leat 2 years before i pulled the truck off the road..... They got here and stopped wearing.... Guess i shoukdnt complain but so much ive gotten, 7 or 8 years out of them!!!
0 2016/06/07 18:50:23
Since the tires i want have been discontinued i settled for a bfg at.... Now to find 2 or 3 more....this exact tire is the d loadrange atko that theyve discontinued and all the ko2s are e load range.... Cant catch a break, every time i decide on a tire i want they discontinue the damn thing!!!! ill probably pick up one more D load range and then swap to ko2 when i kill the two tires on front....
Since the tires i want have been discontinued i settled for a bfg at.... Now to find 2 or 3 more....this exact tire is the d loadrange atko that theyve discontinued and all the ko2s are e load range.... Cant catch a break, every time i decide on a tire i want they discontinue the damn thing!!!! ill probably pick up one more D load range and then swap to ko2 when i kill the two tires on front....
0 2016/06/07 18:50:26
New grille test fit during paint/mod process!!!
New grille test fit during paint/mod process!!!
0 2016/06/08 12:03:10
New hood for the permanent test fit....
New hood for the permanent test fit....
0 2016/06/08 12:03:27
Stock...
Stock...
0 2016/06/08 12:03:37
Pretty!!!! Serious debating on painting it purple, and leaving the ridges aluminum....
Pretty!!!! Serious debating on painting it purple, and leaving the ridges aluminum....
0 2016/06/10 15:21:49
0 2016/06/11 06:32:00
0 2016/06/11 06:32:12
Rear bracket....
Rear bracket....
0 2016/06/11 06:42:28
Front bracket
Front bracket
0 2016/06/11 06:42:43
Some bright red bushings!!!! Why cant the send black bushings?? I hope the brackets pull in a bit when they get tightened up, to take up some of the slack between the sides of the bracket and the bushings!! Last time i had something with poly bushings, i had to lube the bushing to get them to go in and then the spacer that went in hardly went in without trying to push the other side out.... These almost fell in and spacer slid in with no issues.....
Some bright red bushings!!!! Why cant the send black bushings?? I hope the brackets pull in a bit when they get tightened up, to take up some of the slack between the sides of the bracket and the bushings!! Last time i had something with poly bushings, i had to lube the bushing to get them to go in and then the spacer that went in hardly went in without trying to push the other side out.... These almost fell in and spacer slid in with no issues.....
0 2016/06/11 06:42:49
Dont know how i didnt noticethis before....
Dont know how i didnt noticethis before....
0 2016/06/13 16:45:26
Only slightly bent, i think that was just the worst part of it visually as i unbolted the pan the whole thing kinda shifted as i did....:sigh:
Only slightly bent, i think that was just the worst part of it visually as i unbolted the pan the whole thing kinda shifted as i did....:sigh:
0 2016/06/13 16:45:38
No pretty paint, but at least it doesnt leak!!
No pretty paint, but at least it doesnt leak!!
0 2016/06/13 16:48:36
0 2016/06/13 16:48:42
New gm mount.....
New gm mount.....
0 2016/06/13 16:50:25
.....bad engine mount...... And engine mounts are next couldnt get a good pic of passenger side but this is the driver side....
.....bad engine mount...... And engine mounts are next couldnt get a good pic of passenger side but this is the driver side....
0 2016/06/13 16:50:29
Old block out, getting ready to install add a leaf....had to run a drill bit through the entire leaf pack to get the new pin through it!!
Old block out, getting ready to install add a leaf....had to run a drill bit through the entire leaf pack to get the new pin through it!!
0 2016/06/14 18:06:25
New add a leaf going in
New add a leaf going in
0 2016/06/14 18:06:28
5" block in... FML, ubolts arent long enough!!!
5" block in... FML, ubolts arent long enough!!!
0 2016/06/14 18:06:32
Traction bar bracket in...
Traction bar bracket in...
0 2016/06/14 18:06:36
Old block back in....
Old block back in....
0 2016/06/14 18:06:39
Everything bolted up until i can get the right u bolts!!!
Everything bolted up until i can get the right u bolts!!!
0 2016/06/14 18:06:42
Wee bit close to get bolt through....
Wee bit close to get bolt through....
0 2016/06/14 18:42:19
They made their way into the truck.....oh wait guess the bed doesnt count!!!!
They made their way into the truck.....oh wait guess the bed doesnt count!!!!
0 2016/06/15 14:56:55
I look at the 6l80 today.... Thats about as far as i got!!!
I look at the 6l80 today.... Thats about as far as i got!!!
0 2016/06/15 15:33:02
First off i am not an artist, and this is what i have to work with at moment kinda hard to hold bar up with one hand and take pic with the other, but this is basically what i am talking about, biggest thing is i wouldnt be able to put shocks on em down the road is i decided to figure that little tid bit out, and the pro comp logos would be reversed....
First off i am not an artist, and this is what i have to work with at moment kinda hard to hold bar up with one hand and take pic with the other, but this is basically what i am talking about, biggest thing is i wouldnt be able to put shocks on em down the road is i decided to figure that little tid bit out, and the pro comp logos would be reversed....
0 2016/06/16 17:08:32
0 2016/06/16 17:27:36
0 2016/06/16 17:27:40
0 2016/06/16 17:27:43
Transfer case adaptor for the 6l80 came in today.... Also got my shifter this morning but left it in my toolbox at work.....
Transfer case adaptor for the 6l80 came in today.... Also got my shifter this morning but left it in my toolbox at work.....
0 2016/06/20 15:26:11
Got new u bolts and blocks installed
Got new u bolts and blocks installed
0 2016/06/23 18:28:26
0 2016/06/23 18:28:32
0 2016/06/23 18:28:35
Went ahead and put bars in the rear mounts didnt have time to drill through the frame
Went ahead and put bars in the rear mounts didnt have time to drill through the frame
0 2016/06/23 18:28:40
0 2016/06/23 18:28:48
Other side went a bit quicker....
Other side went a bit quicker....
0 2016/06/23 18:28:51