GM Engine & Exhaust Performance EFI | GEN I/GEN II/GEN III/GEN IV Engines |Small Block | Big Block |

Anyone who has a GOOD amount of exhaust experience please help.

Old Jan 22, 2013 | 01:14 PM
  #31  
Suburbazine's Avatar
TECH Fanatic
 
Joined: Feb 2009
Posts: 1,635
Likes: 1
From: Baton Rouge, LA
Default

That camera is not reproducing the sound very well, it's using a compressor to limit the sound peaks. The actual waveform should have more low end and more amplitude.

I ran a 10 series on a 5" tip. Loud as hell, but too much bass pulse with my cam. When the cam chops, the pulse will chop right through nearby buildings...
Reply
Old Jan 22, 2013 | 01:44 PM
  #32  
Mangled03gmc's Avatar
Baltimore Whore
20 Year Member
iTrader: (95)
 
Joined: Apr 2004
Posts: 16,820
Likes: 2
From: In a van DOWN BY THE RIVER
Default

https://www.youtube.com/watch?v=D4JX...qRBRhg&index=7
2 3'' to Y and single 4 all the way back.
Reply
Old Jan 22, 2013 | 06:17 PM
  #33  
GMCtrk's Avatar
TECH Senior Member
iTrader: (27)
 
Joined: Jul 2004
Posts: 12,275
Likes: 19
From: Dallas
Default

Originally Posted by Mangled03gmc
https://www.youtube.com/watch?v=D4JX...qRBRhg&index=7
2 3'' to Y and single 4 all the way back.
Jeez John, that thing is loud. What are the specs on that edelbrock muffler?

Just bought a 24" magnaflow to replace my 15" mbrp. If its not reasonably quiet I'm going to just chalk it up to the 4" and roll with it.
Reply
Old Jan 22, 2013 | 10:13 PM
  #34  
Silverado Street Machine's Avatar
Thread Starter
Staging Lane
 
Joined: Jan 2012
Posts: 75
Likes: 0
From: Pennsylvania
Default

Originally Posted by Suburbazine
That camera is not reproducing the sound very well, it's using a compressor to limit the sound peaks. The actual waveform should have more low end and more amplitude.

I ran a 10 series on a 5" tip. Loud as hell, but too much bass pulse with my cam. When the cam chops, the pulse will chop right through nearby buildings...
So you're saying the sound isn't even close to that growl?
Reply
Old Jan 23, 2013 | 12:46 AM
  #35  
Suburbazine's Avatar
TECH Fanatic
 
Joined: Feb 2009
Posts: 1,635
Likes: 1
From: Baton Rouge, LA
Default

Originally Posted by Silverado Street Machine
So you're saying the sound isn't even close to that growl?
Yes. It's basically a single baffle muffler, one step short of straight pipes.

If you noticed when he was pulling onto the street, you could hear the tires crunching over the exhaust. That muffler is nowhere near that quiet at idle or off idle...the only reason it sounded like it had a growl was because he has a stock cam in there. It's loud, but only the only difference over a 40 series is the 10 series passes a little more low range and a lot more high range. (aka NOISE)

Last edited by Suburbazine; Jan 23, 2013 at 12:51 AM.
Reply
Old Jan 23, 2013 | 04:05 PM
  #36  
Silverado Street Machine's Avatar
Thread Starter
Staging Lane
 
Joined: Jan 2012
Posts: 75
Likes: 0
From: Pennsylvania
Default

Originally Posted by Suburbazine
Yes. It's basically a single baffle muffler, one step short of straight pipes.

If you noticed when he was pulling onto the street, you could hear the tires crunching over the exhaust. That muffler is nowhere near that quiet at idle or off idle...the only reason it sounded like it had a growl was because he has a stock cam in there. It's loud, but only the only difference over a 40 series is the 10 series passes a little more low range and a lot more high range. (aka NOISE)
Well then I need to get my hands on a Borla ATAK muffler and modify or try finding a Corsa Sport db somewhere. I didn't think it would be this difficult to replicate a sound.
Reply
Old Jan 23, 2013 | 04:20 PM
  #37  
Mangled03gmc's Avatar
Baltimore Whore
20 Year Member
iTrader: (95)
 
Joined: Apr 2004
Posts: 16,820
Likes: 2
From: In a van DOWN BY THE RIVER
Default

Originally Posted by GMCtrk
Jeez John, that thing is loud. What are the specs on that edelbrock muffler?

Just bought a 24" magnaflow to replace my 15" mbrp. If its not reasonably quiet I'm going to just chalk it up to the 4" and roll with it.
LOl, yeh it is loud at idle, driving isn't too bad. Uhh case size is about 27'' x 9''
Reply
Old Jan 23, 2013 | 04:30 PM
  #38  
Suburbazine's Avatar
TECH Fanatic
 
Joined: Feb 2009
Posts: 1,635
Likes: 1
From: Baton Rouge, LA
Default

Originally Posted by Silverado Street Machine
Well then I need to get my hands on a Borla ATAK muffler and modify or try finding a Corsa Sport db somewhere. I didn't think it would be this difficult to replicate a sound.
Both of those will sound like crap behind a truck engine and truck headers. If you can find one give it a shot and let us know how it turned out.

The Borla and Corsa mufflers use tuned box sound cancelling to limit the sound level while keeping that signature note...on specifically measured and matched vehicles. For instance, take a 2010 Camaro with Corsa mufflers. Add longtubes. Now, the car sounds normal from 0-2200RPM, but when you get on it the muffler puts out a loud raspy noise like a blown speaker being overdriven.

If you are looking for something similar in design to the ATAK I'd recommend looking at Goerlich Xlerator mufflers. They're not tuned to specific vehicles and are a whole lot easier to find.

Last edited by Suburbazine; Jan 23, 2013 at 04:35 PM.
Reply
Old Jan 23, 2013 | 04:54 PM
  #39  
Silverado Street Machine's Avatar
Thread Starter
Staging Lane
 
Joined: Jan 2012
Posts: 75
Likes: 0
From: Pennsylvania
Default

Never even heard of them, but I'll definitely check them out!
Reply
Old Jan 23, 2013 | 04:57 PM
  #40  
Silverado Street Machine's Avatar
Thread Starter
Staging Lane
 
Joined: Jan 2012
Posts: 75
Likes: 0
From: Pennsylvania
Default

If you can find any good clips of what they sound like on a 5.3 let me know, I'm having trouble finding any.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
pittman
Drag Racing
37
Jan 19, 2016 07:06 AM
Cm_gmt800
GM Engine & Exhaust Performance
8
Aug 3, 2015 09:13 PM
LARRY01Z28
GMT 800 & Older GM General Discussion
1
Aug 1, 2015 10:15 PM
Suburban2500
GMT 800 & Older GM General Discussion
2
Jul 14, 2015 02:10 AM
cwylie
GMT 800 & Older GM General Discussion
4
Jul 7, 2015 11:42 AM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 08:37 AM.