GMT 900 Trucks General Discussion 2007 - 2013 Trucks | General Discussion

2013 a/c issue

Old Mar 20, 2014 | 11:05 PM
  #1  
Thread Starter
12 Second Truck Club
iTrader: (18)
 
Joined: Aug 2008
Posts: 1,107
Likes: 0
From: Cypress, TX
Default 2013 a/c issue

pulled supercharger off last weekend, unhooked battery for 4 days while alternator was off. hooked it all back up last night, flashed in the header only tune, now my damn a/c will only blow on floor and defrost. WTF?????? very irritating. ive unhooked batt and let itsit, pulled fuses, what the heck could it be?

Last edited by 06tx4.8; Mar 20, 2014 at 11:21 PM.
Reply
Old Mar 21, 2014 | 01:36 AM
  #2  
TECH Veteran
20 Year Member
iTrader: (36)
 
Joined: Oct 2004
Posts: 4,985
Likes: 54
From: somewhere in TX
Default

Try this first and see what it does this for the electronic dual zone system that 95 percent of us have. This is the actuator recalibration sequence if you do not have a tech 2. It may have had a brain fart if the below doesn't fix it then it's probably a failed mode door actuator.


Do not adjust any controls on the HVAC control module while the HVAC control module is self-calibrating. If interrupted, improper HVAC performance will result.

Clear all DTCs.
Place the ignition switch to the OFF position.
Install the HVAC actuator.
Connect all previously disconnected components.
Remove the HVAC/ECAS fuse for a minimum of 10 seconds.
Install the HVAC/ECAS fuse.
Start the vehicle.
Wait 40 seconds for the HVAC control module to self-calibrate.
Verify that no DTCs have set as current DTCs

Last edited by 01WS6/tamu; Mar 21, 2014 at 01:44 AM.
Reply
Old Mar 21, 2014 | 09:20 AM
  #3  
Thread Starter
12 Second Truck Club
iTrader: (18)
 
Joined: Aug 2008
Posts: 1,107
Likes: 0
From: Cypress, TX
Default

no luck
Reply
Old Mar 22, 2014 | 06:09 PM
  #4  
TECH Veteran
20 Year Member
iTrader: (36)
 
Joined: Oct 2004
Posts: 4,985
Likes: 54
From: somewhere in TX
Default

Well without having a tech 2 to look at data and do a actuator test it's only a guess. But my assumption is the mode door actuator failed. Get one from a dealer it's kinda a pita to install but doable. It's to the right of the gas pedal above the trans tunnel on the vertical side of the airbox.

Then once replaced you have to do the recalibration sequence posted above.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Idryfly5
GMT 900 Trucks General Discussion
2
Sep 2, 2022 08:55 PM
murderedSS
Tuning, Diagnostics, Electronics, and Wiring
27
Oct 12, 2015 11:13 AM
MA$TER_E
Tuning, Diagnostics, Electronics, and Wiring
5
Sep 9, 2015 03:14 PM
the owl
Trucks and SUV Classifieds
0
Sep 4, 2015 04:09 PM
Hpinnovate
Tuning, Diagnostics, Electronics, and Wiring
0
Sep 4, 2015 02:28 AM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 03:31 PM.