Iron LS1 shortblock, Nitrous plate, ASP UD pulley, Comp 7.4 pushrods, Roll pan
Nov 22, 2011 | 05:57 PM
#1
Iron LS1 shortblock, Nitrous plate, ASP UD pulley, Comp 7.4 pushrods, Roll pan
Iron LS1 short block for sale, was built professionally by Haynes racing in Malden Missouri. The short block was dissassembled, hot tanked, rods cleaned, crank cleaned and polished, block bored and honed. cam, cam bearings and timing set installed, cam degreed, rotating assembly balanced and the short block assembled. Short block is FRESH 0 miles since built.
The short block consists of a 20,000+/- mile 5.3 block which was bored to the factory 3.898 ls1 bore. Mahle Forged pistons with -4cc valve reliefs,Mahle rings and wrist pins, Stock reconditioned rods, stock polished crank, Clevite H main bearings, clevite H rod bearings, Clevite cam bearings, ARP Pro series Main studs, ARP pro Series Rod bolts, ARP 12 point headstuds, ARP cam and ARP cam retainer bolts. The cam in this engine is an Engine Power Systems custom ground cam, Spec'd by Patrick Guerra, 222/230 .596/.600 112+4LSA. Timing set is a Cloyes 9-3158AZ hex adjust timing set with their "z" chain, supposed to be the toughest made.
Comes with an oil pump, all sensors, new Fel Pro gasket kit(back cover gasket already installed and torqued to spec), Timing cover, valve covers, lifter valley cover, oil pan, lifter trays, all hardware , and knock sensors with harness. Asking 2000 OBO price is negotiable and might trade for somethin cool. For the right price can help arrange shipping or maybe deliver if close enough. WILL TRADE ON THIS. REDUCED- $1600
Reduced again- 1600 or best offer!
This week only 1300 for the shortblock!!
Also have a nitrous outlet 78mm plate kit for truck intakes, all hardware and a bag of misc jets included. Brand new never ran, 180 shipped
ASP underdrive pulley for 4.8-6.0 trucks, comes with alternator pulley and gates belt to fit. SOLD
Comp 7.4 length hardened pushrods brand new box- SOLD
Stock truck intake- Comes with everything you see in the pics, egr and evap blocked- 50 shipped.
Low mileage truck coils, with brackets, harnesses, and MSD wires- 105 shipped
Custom Classics rollpan liscense recess on passenger side, fits 88-98 chevy trucks, 115 shipped.
Prices are all OBO if you dont like the price make me an offer, thanks.
Here is my attempt to get a picture of the main studs
The short block consists of a 20,000+/- mile 5.3 block which was bored to the factory 3.898 ls1 bore. Mahle Forged pistons with -4cc valve reliefs,Mahle rings and wrist pins, Stock reconditioned rods, stock polished crank, Clevite H main bearings, clevite H rod bearings, Clevite cam bearings, ARP Pro series Main studs, ARP pro Series Rod bolts, ARP 12 point headstuds, ARP cam and ARP cam retainer bolts. The cam in this engine is an Engine Power Systems custom ground cam, Spec'd by Patrick Guerra, 222/230 .596/.600 112+4LSA. Timing set is a Cloyes 9-3158AZ hex adjust timing set with their "z" chain, supposed to be the toughest made.
Comes with an oil pump, all sensors, new Fel Pro gasket kit(back cover gasket already installed and torqued to spec), Timing cover, valve covers, lifter valley cover, oil pan, lifter trays, all hardware , and knock sensors with harness. Asking 2000 OBO price is negotiable and might trade for somethin cool. For the right price can help arrange shipping or maybe deliver if close enough. WILL TRADE ON THIS. REDUCED- $1600
Reduced again- 1600 or best offer!
This week only 1300 for the shortblock!!
Also have a nitrous outlet 78mm plate kit for truck intakes, all hardware and a bag of misc jets included. Brand new never ran, 180 shipped
ASP underdrive pulley for 4.8-6.0 trucks, comes with alternator pulley and gates belt to fit. SOLD
Comp 7.4 length hardened pushrods brand new box- SOLD
Stock truck intake- Comes with everything you see in the pics, egr and evap blocked- 50 shipped.
Low mileage truck coils, with brackets, harnesses, and MSD wires- 105 shipped
Custom Classics rollpan liscense recess on passenger side, fits 88-98 chevy trucks, 115 shipped.
Prices are all OBO if you dont like the price make me an offer, thanks.
Here is my attempt to get a picture of the main studs
Last edited by EthanH; Dec 29, 2011 at 11:34 PM.