Forged Pistons, Nitrous stuff, Pro flo edelbrock intake, dedicated cell etc..
#1
TECH Resident
Thread Starter
iTrader: (12)
Join Date: Dec 2005
Location: woodstock GA
Posts: 897
Likes: 0
Received 0 Likes
on
0 Posts
Forged Pistons, Nitrous stuff, Pro flo edelbrock intake, dedicated cell etc..
Few things gotta go!!!
Edelbrock Pro Flo Intake for GM Cathedral lsx heads, Has a four solenoid direct port plumbed on it, the intake is the black version and is 520$... The kit is a nitrous outled four-noid direct port which is around 700$ plus Milling/drilling/plumbing/tubing intake is plumbed and ready to bolt on-1250$ obo
I also have a 15lb nitrous outlet bottle with glow-in-the-dark pressure gauge in the neck... its been used so yes it has a few scratches, its black 264.99 new- 225$ obo
Also have an FJO mini nitrous controller for tps/window/progression and will run two stages, has trans-brake delay mode and runs rpm based ramps and time based ramps- 220$ obo, good luck finding one. FJO Racing Products - Progressive Nitrous Mini-Controller
I have a -6 feed line I believe to be about 10 feet long w black fittings 40$
Or a 20 foot -6 feed with black fittings for 65$
Also i have a dedicated fuel system for nitrous, it's a 1 gallon cell with a submerged factory z06 efi fuel pump, aeromotive return style regulator with black fittings and a white faced autometer gauge, ready to run 400$ obo
Also have a set of 2618 Manley/SDPC 4.005 bore +10cc dome pistons for 6.125 rods, full floating pin, used about 20 passes 400$ obo
Edelbrock Pro Flo Intake for GM Cathedral lsx heads, Has a four solenoid direct port plumbed on it, the intake is the black version and is 520$... The kit is a nitrous outled four-noid direct port which is around 700$ plus Milling/drilling/plumbing/tubing intake is plumbed and ready to bolt on-1250$ obo
I also have a 15lb nitrous outlet bottle with glow-in-the-dark pressure gauge in the neck... its been used so yes it has a few scratches, its black 264.99 new- 225$ obo
Also have an FJO mini nitrous controller for tps/window/progression and will run two stages, has trans-brake delay mode and runs rpm based ramps and time based ramps- 220$ obo, good luck finding one. FJO Racing Products - Progressive Nitrous Mini-Controller
I have a -6 feed line I believe to be about 10 feet long w black fittings 40$
Or a 20 foot -6 feed with black fittings for 65$
Also i have a dedicated fuel system for nitrous, it's a 1 gallon cell with a submerged factory z06 efi fuel pump, aeromotive return style regulator with black fittings and a white faced autometer gauge, ready to run 400$ obo
Also have a set of 2618 Manley/SDPC 4.005 bore +10cc dome pistons for 6.125 rods, full floating pin, used about 20 passes 400$ obo
#3
TECH Resident
Thread Starter
iTrader: (12)
Join Date: Dec 2005
Location: woodstock GA
Posts: 897
Likes: 0
Received 0 Likes
on
0 Posts
EDL-71393
The only difference in the two is that one has an ls2 style o-ring and the other u have to run a gasket... This one has been drilled to accept ls2 throttle bodies as well... TTT
Fuel rails are not included, But they [I]can[I] be
The only difference in the two is that one has an ls2 style o-ring and the other u have to run a gasket... This one has been drilled to accept ls2 throttle bodies as well... TTT
Fuel rails are not included, But they [I]can[I] be