PerformanceTrucks.net Forums

GM Engine & Exhaust Performance EFI | GEN I/GEN II/GEN III/GEN IV Engines |Small Block | Big Block |

tbss swap last question?

   
Old Apr 5, 2011 | 01:08 PM
  #11  
mhotrodscooter's Avatar
mhotrodscooter
TECH Fanatic
iTrader: (13)
 
Joined: Apr 2010
Posts: 1,750
Likes: 0
From: jennings,louisiana
Default
Go from the valve cover vent to the intake tube. It doesn't matter if you don't have a flat spot or not. Just connect it the best way you know how..
Mine after swap
Reply
0
Old Apr 5, 2011 | 01:10 PM
  #12  
LaCamionetaGris's Avatar
LaCamionetaGris
Thread Starter
On The Tree
iTrader: (2)
 
Joined: Aug 2008
Posts: 132
Likes: 1
From: Stationed in VA.
Default
yes i gotta clean it up where did bolt on the x link, i thought the vortec cover would bolt on looks good
Reply
0
Old Apr 5, 2011 | 01:12 PM
  #13  
LaCamionetaGris's Avatar
LaCamionetaGris
Thread Starter
On The Tree
iTrader: (2)
 
Joined: Aug 2008
Posts: 132
Likes: 1
From: Stationed in VA.
Default
so do i plug the hole on the intake then?
FINALLY REACECHED THE 100 POST MARK
Reply
0
Old Apr 5, 2011 | 01:17 PM
  #14  
mhotrodscooter's Avatar
mhotrodscooter
TECH Fanatic
iTrader: (13)
 
Joined: Apr 2010
Posts: 1,750
Likes: 0
From: jennings,louisiana
Default
I don't have my truck or pictures to show how it's done.. I mounted link to a bolt on passengerside of intake on top right behind tb a little ways. I made a L shape bracket.
Reply
0
Old Apr 5, 2011 | 01:23 PM
  #15  
mhotrodscooter's Avatar
mhotrodscooter
TECH Fanatic
iTrader: (13)
 
Joined: Apr 2010
Posts: 1,750
Likes: 0
From: jennings,louisiana
Default
What hole in intake or you talking about?
Reply
0
Old Apr 5, 2011 | 01:33 PM
  #16  
Dezert1500's Avatar
Dezert1500
TECH Enthusiast
iTrader: (11)
 
Joined: Jul 2005
Posts: 523
Likes: 0
Default
Yes, plug the hole on the intake. That hole is meant for the valley cover breather line that comes off GenIV's valley cover.

Tap the intake tube and run a vacuum tube from the passenger valve cover to it.
Reply
0
Old Apr 5, 2011 | 01:42 PM
  #17  
Dezert1500's Avatar
Dezert1500
TECH Enthusiast
iTrader: (11)
 
Joined: Jul 2005
Posts: 523
Likes: 0
Default
This is the only pic I have and it's hard to tell, but you can see where I ran the vacuum line to the intake tube.



Here's the kit I used. Spectre Part# 9712
Reply
0
Old Apr 5, 2011 | 02:34 PM
  #18  
AndysC3's Avatar
AndysC3
TECH Addict
iTrader: (14)
 
Joined: Jun 2009
Posts: 2,884
Likes: 10
From: Minot, ND
Default
Originally Posted by Dezert1500
Here's the kit I used. Spectre Part# 9712
so for this, all you did was drill a hole in the intake tube and use the correct fitting? any leaks?
Reply
0
Old Apr 5, 2011 | 03:30 PM
  #19  
1slowz71's Avatar
1slowz71
TECH Fanatic
iTrader: (6)
 
Joined: Jul 2010
Posts: 1,091
Likes: 1
From: SO-CAL 818 TO D' 805
Default
What year of a vette is the fuel filter yoi used ? And can't 0you just put a regulas air filter to that hose it just a breather ain't it ?
Reply
0
Old Apr 5, 2011 | 03:31 PM
  #20  
Dezert1500's Avatar
Dezert1500
TECH Enthusiast
iTrader: (11)
 
Joined: Jul 2005
Posts: 523
Likes: 0
Default
Originally Posted by AndysC3
so for this, all you did was drill a hole in the intake tube and use the correct fitting? any leaks?
Zero leaks, just make sure the hole is drilled to the correct size.
Reply
0

Thread Tools
Search this Thread
Search this Thread:

Advanced Search

Advanced Search

All times are GMT -5. The time now is 01:18 PM.