GM Engine & Exhaust Performance EFI | GEN I/GEN II/GEN III/GEN IV Engines |Small Block | Big Block |

soo, how bad do you guys want to see what the 4.8 can put out?

Thread Tools
 
Search this Thread
 
Old Nov 26, 2004 | 04:19 PM
  #61  
IMD's Avatar
IMD
Banned
iTrader: (10)
 
Joined: Sep 2004
Posts: 567
Likes: 0
From: Texas
Default

Originally Posted by hellbents10
I can tell you what will happen the convetional if done right will make the said vehicle go down the track faster.
well you, and i, and other intelligent people agree with that, but id sure like to see some back to back numbers once and for all.
Old Nov 27, 2004 | 03:18 AM
  #62  
parish8's Avatar
Thread Starter
single digit dreamer
iTrader: (6)
 
Joined: Mar 2002
Posts: 9,743
Likes: 2
From: omaha ne
Default

woohoo, got the $150, now it is time for me to get ready. we got rid of the low end miss with the magasquirt and it is running great, we did about 20 wot 1/4 mile runs messing with the fueling and slowly turning up the boost. we were over 11psi on pump gas and no knock. there is a noticable diference in power between 9psi and 11psi.

AND we did it in the rain. 4wd kicks ***!!
Old Nov 27, 2004 | 09:55 AM
  #63  
TECH Fanatic
 
Joined: May 2004
Posts: 1,125
Likes: 0
From: Lincoln, NE
Default

nice work jim can't wait to see the results! sounds like you are havin fun
Old Nov 27, 2004 | 01:50 PM
  #64  
hellbents10's Avatar
LS1Tech Sponsor
iTrader: (10)
 
Joined: Mar 2004
Posts: 4,148
Likes: 0
From: Spring Lake, MI
Default

Are you using the megasquirt with a 3 bar then? So you just have the megasquirt tied into the tach signal ramed up to 12v for the dquirt vs the stock 0-9v reading? Then you just have power to the MS and wired into the injectors and using MAP RPM and VE to fuel the motor? Sorry for all the questions, the megasquirt has grabbed my attention now. Its really cheap too. Are you in closed loop at WOT with a wideband or open loop like a factory PCM? Ok better stop asking questions now before I have a book on here.lol.
Old Nov 27, 2004 | 02:00 PM
  #65  
parish8's Avatar
Thread Starter
single digit dreamer
iTrader: (6)
 
Joined: Mar 2002
Posts: 9,743
Likes: 2
From: omaha ne
Default

it has a 2.5bar sensor, ~22psi

we used a "pull up circuit" on the tach lead. the stock signal is 9v, with the mega hooked up it pulled it down to under 2v we reduced the resistance on the pull up circuit till the mega stated working and that was a little over 2v. the stock tach still didn't work though so we kept droping the resistance till we were back at a 9volt square wave signal. at that point both the mega and the stock tach worked.

we hooked in the stock tps, also a seperate IAT and coolant temp. then wired in the injectors. so far it is working well. we tried hooking up the nitrous control and so far it isn't working quite like we had hoped. we still need to do some research on that one.
Old Nov 27, 2004 | 02:05 PM
  #66  
13 Second Truck Club
iTrader: (1)
 
Joined: Mar 2003
Posts: 4,094
Likes: 1
From: Pueblo de Nuestra Señora la Reina de los Ángeles de la Porciúncula
Default

Originally Posted by parish8
yeah, ok. i am sure it would only take a few minutes to fab that up.
Well then why don't you collect more money from these guys then? You want us to pay for your 408 too?
I wish I was a mod so I could abuse my status to beg for money...how come when parish says he'll make 400RWHP on a 4.8 it's gospel, but when Blownchevy says 400RWHP on a 5.3, it's bullshit?
If it were anyone else asking for money, everyone would laugh....oh yea
Old Nov 27, 2004 | 02:07 PM
  #67  
13 Second Truck Club
iTrader: (1)
 
Joined: Mar 2003
Posts: 4,094
Likes: 1
From: Pueblo de Nuestra Señora la Reina de los Ángeles de la Porciúncula
Default

I'm sure parish will erase that post now
Old Nov 27, 2004 | 02:11 PM
  #68  
parish8's Avatar
Thread Starter
single digit dreamer
iTrader: (6)
 
Joined: Mar 2002
Posts: 9,743
Likes: 2
From: omaha ne
Default

Originally Posted by Chingon
Well then why don't you collect more money from these guys then? You want us to pay for your 408 too?
I wish I was a mod so I could abuse my status to beg for money...how come when parish says he'll make 400RWHP on a 4.8 it's gospel, but when Blownchevy says 400RWHP on a 5.3, it's bullshit?
If it were anyone asking for money, everyone would laugh....oh yea
thats nice . my question here is does anyone want to see what the 4.8 can do if pushed to it's limit. i am willing to kill the 4.8 if others are willing to pay for the dyno and fuel.

seems that a few people are interested in seeing what it can do and are willing to cough up a few bucks to see it. thanks guys, this is going to be fun.

if this turns ugly posts will just get deleted.
Old Nov 27, 2004 | 02:19 PM
  #69  
13 Second Truck Club
iTrader: (1)
 
Joined: Mar 2003
Posts: 4,094
Likes: 1
From: Pueblo de Nuestra Señora la Reina de los Ángeles de la Porciúncula
Default

Old Nov 27, 2004 | 02:24 PM
  #70  
13 Second Truck Club
iTrader: (1)
 
Joined: Mar 2003
Posts: 4,094
Likes: 1
From: Pueblo de Nuestra Señora la Reina de los Ángeles de la Porciúncula
Default

How was me posting a laughing smiley an "ugly" post?



All times are GMT -5. The time now is 02:11 PM.