Ok monday it's cam day whats the best setup with stall?
Jan 25, 2009 | 10:54 PM
#21
Thread Starter
TECH Apprentice
Joined: Jan 2009
Posts: 347
Likes: 0
From: dallas texas
I dunno, never ran my truck in the 1/4, but when it was stockish, it ran 9.8 in the 1/8th, now it runs 8.5... IMO the 4.8 needs a small diameter converter since it is low on TQ. The smaller diameter TC will allow it to stall higher... The cam i posted is what I am going to change too, in a few weeks, when I swap out my heads... for a cam definately get a 112 LSA and some advance ground into it, the 4.8 does not make decent TQ until later in the powerband, the tight lsa and advance brings the power in sooner, which the 4.8 definately needs...
Just my opinion, take it as you will
Just my opinion, take it as you will
Jan 25, 2009 | 11:00 PM
#22
IMO I'd go with a Yank SS3200 converter. I have an SS3600 and drive it daily; and that's with the stock cam. The 4.8 needs a little more stall to get it in the powerband. As for cams; look at the TR or TSP 220, Comp 222/224, or the Comp 224/220.
Actually; the Vinci "Trucker" cam with a TT3000 would be a good mild combo as well. Its a 216/224 .551 and would be well suited. Its on a 115 lsa so it'll have a mild idle but would make a killer combo on a small motor.
Actually; the Vinci "Trucker" cam with a TT3000 would be a good mild combo as well. Its a 216/224 .551 and would be well suited. Its on a 115 lsa so it'll have a mild idle but would make a killer combo on a small motor.
Jan 26, 2009 | 03:57 PM
#27
Thread Starter
TECH Apprentice
Joined: Jan 2009
Posts: 347
Likes: 0
From: dallas texas
well what do you guys think of and lunati cam the rmp will kick in more like at 1500-1800 with a street fighter tci 10''3000 stall
Advertised Duration (Int/Exh): 283/283
Duration @ .050 (Int/Exh): 221/221
Gross Valve Lift (Int/Exh): .558/.558
LSA/ICL: 114/110
Valve Lash (Int/Exh): Hyd/Hyd
RPM Range: 2500-6000
Advertised Duration (Int/Exh): 283/283
Duration @ .050 (Int/Exh): 221/221
Gross Valve Lift (Int/Exh): .558/.558
LSA/ICL: 114/110
Valve Lash (Int/Exh): Hyd/Hyd
RPM Range: 2500-6000
Jan 26, 2009 | 04:23 PM
#29
Staging Lane
Joined: Jan 2009
Posts: 51
Likes: 0
If you are willing to go with a mid-size Lunati, why not go with this with the tight LSA and make some real noise?
Advertised Duration (Int/Exh): 283/293
Duration @ .050 (Int/Exh): 224/224
Gross Valve Lift (Int/Exh): .560/.560
LSA/ICL: 112/108
Valve Lash (Int/Exh): Hyd/Hyd
RPM Range: 2500-6000
Includes: Cam Only
Part Number: 55006LUN
Advertised Duration (Int/Exh): 283/293
Duration @ .050 (Int/Exh): 224/224
Gross Valve Lift (Int/Exh): .560/.560
LSA/ICL: 112/108
Valve Lash (Int/Exh): Hyd/Hyd
RPM Range: 2500-6000
Includes: Cam Only
Part Number: 55006LUN
