PerformanceTrucks.net Forums

GM Engine & Exhaust Performance EFI | GEN I/GEN II/GEN III/GEN IV Engines |Small Block | Big Block |

Codes after cam install???

Thread Tools
 
Search this Thread
 
Old Sep 15, 2008 | 10:06 PM
  #1  
nickpc82
Thread Starter
TECH Enthusiast
iTrader: (24)
 
Joined: May 2007
Posts: 646
Likes: 0
From: Stockton, Ca
Default Codes after cam install???
I just did my cam swap, I havent got it tuned yet, now I'm throwing the
P0102 code. Any ideas? Is this normal after a cam swap? Thanks.

Nick
Reply
0
Old Sep 15, 2008 | 10:31 PM
  #2  
viciousknid's Avatar
viciousknid
Where's the Beef?
iTrader: (8)
 
Joined: Jan 2007
Posts: 9,382
Likes: 1
From: Dover, Oklahoma
Default
Mine has had that code for a while.
Did you cut/repair the wires on your MAF sensor?
Reply
0
Old Sep 15, 2008 | 10:51 PM
  #3  
nickpc82
Thread Starter
TECH Enthusiast
iTrader: (24)
 
Joined: May 2007
Posts: 646
Likes: 0
From: Stockton, Ca
Default
No. But I did recharge my air filter and sprayed air mass cleaner on my air mass before I started it...
Reply
0
Old Sep 16, 2008 | 12:14 PM
  #4  
viciousknid's Avatar
viciousknid
Where's the Beef?
iTrader: (8)
 
Joined: Jan 2007
Posts: 9,382
Likes: 1
From: Dover, Oklahoma
Default
If you over oil your filter some of the oil blows thru onto the MAF causing it to throw codes. I'd take the MAF back out and clean it up again.
Reply
0
Old Sep 16, 2008 | 07:29 PM
  #5  
nickpc82
Thread Starter
TECH Enthusiast
iTrader: (24)
 
Joined: May 2007
Posts: 646
Likes: 0
From: Stockton, Ca
Default
I did that but I didnt need to. I had my cousin help me and he forgot to plug in the MAF so problem fixed.
Reply
0
Old Sep 16, 2008 | 09:42 PM
  #6  
hirdlej's Avatar
hirdlej
TECH Junkie
iTrader: (31)
 
Joined: Dec 2004
Posts: 3,471
Likes: 1
From: Minneapolis, MN
Default
Don't forget to do a case relearn
Reply
0
Old Sep 16, 2008 | 09:52 PM
  #7  
nickpc82
Thread Starter
TECH Enthusiast
iTrader: (24)
 
Joined: May 2007
Posts: 646
Likes: 0
From: Stockton, Ca
Default
What is that???
Reply
0
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
2006 RCSB 4x4 V6 to V8 LQ9 Cammed Manual 5 Speed Swap
ARC
GMT 800 & Older GM General Discussion
57
Feb 21, 2022 10:54 AM
Speed Shops in VA for Cam Install
all_individual
Eastern
6
Oct 10, 2015 10:09 PM
P0336 code need help
chevyl33
GM Engine & Exhaust Performance
6
Aug 24, 2015 08:21 AM
Speed Shops in VA for Cam Install?
all_individual
Silverado SS, Joe Gibbs Editions, SSR
1
Jul 13, 2015 11:01 AM
HELP NEEDED OBS LQ9 swap going into reduced engine power mode
GreyChevy
Tuning, Diagnostics, Electronics, and Wiring
1
Jul 7, 2015 08:57 PM
Back to Subforum
GM Engine & Exhaust Performance
View Next Unread
out with the old, in with the new




Advanced Search

All times are GMT -5. The time now is 03:05 PM.