FS-02 rcsb chevy-cammed, stalled, etc.
06-10-2009, 09:56 AM
#1
TECH Apprentice
Thread Starter
iTrader: (3)
Join Date: Jul 2007
Location: Alma, Ga
Posts: 348
Likes: 0
Received 0 Likes
on
0 Posts
FS-02 rcsb chevy-cammed, stalled, etc.
!!!!PRICE REDUCED!!! $9,000 with stock wheels
I am selling my 2002 chevy silverado. It just rolled over to 80000 on the clock. I hate to sell it but Im going a different direction and the wife is wanting a baby so the truck goes. I will also include the 3.42 gears and factory wheels with m/t drag radials. I also have everything to make a set of long bars for it exept the tubing. It has a rebuilt Ga title. The 6.0 had about 30000 on it when bought and was installed in the truck at 76000. I dont want to put any more money into it cause not sure of the job. Price is $10000
Engine-
6.0 lq4- around 34000 miles
Comp Cams-224/224 581/581 112
Comp 918 springs
Tsp hardened 7.4 push rods
K&n cai
E-fans
8.1l inj.
Jet tb spacer
Pacesetter longtubes
or-y pipe
Cut-out
Flowmaster 40 series
optima battery
Drivetrain-
Built 4l60e
Tci 3000
Hayden trans cooler
4.10 gears
Richmond powertrax locker
and 3.42 gears
Exterior-
4-6 drop
street scene mirrors
Roll pan molded in
Shaved tailgate
Cowl hood
Clear parking lights
03 rear tail lights
Tinted windows
Bed cover
billit ant.
Panted grill with inserts
polished bowtie
also includes stock wheels with m/t dr's
Interior-
3 gauge pillar pod
Trans temp gauge
Air/ fuel gauge
clear gauge needles
The bad-
Tranny lost o/d
Front has some paint chips
Tailgate and rollpan needs painted
I am selling my 2002 chevy silverado. It just rolled over to 80000 on the clock. I hate to sell it but Im going a different direction and the wife is wanting a baby so the truck goes. I will also include the 3.42 gears and factory wheels with m/t drag radials. I also have everything to make a set of long bars for it exept the tubing. It has a rebuilt Ga title. The 6.0 had about 30000 on it when bought and was installed in the truck at 76000. I dont want to put any more money into it cause not sure of the job. Price is $10000
Engine-
6.0 lq4- around 34000 miles
Comp Cams-224/224 581/581 112
Comp 918 springs
Tsp hardened 7.4 push rods
K&n cai
E-fans
8.1l inj.
Jet tb spacer
Pacesetter longtubes
or-y pipe
Cut-out
Flowmaster 40 series
optima battery
Drivetrain-
Built 4l60e
Tci 3000
Hayden trans cooler
4.10 gears
Richmond powertrax locker
and 3.42 gears
Exterior-
4-6 drop
street scene mirrors
Roll pan molded in
Shaved tailgate
Cowl hood
Clear parking lights
03 rear tail lights
Tinted windows
Bed cover
billit ant.
Panted grill with inserts
polished bowtie
also includes stock wheels with m/t dr's
Interior-
3 gauge pillar pod
Trans temp gauge
Air/ fuel gauge
clear gauge needles
The bad-
Tranny lost o/d
Front has some paint chips
Tailgate and rollpan needs painted
Last edited by getonit; 09-18-2009 at 11:05 PM.
06-12-2009, 12:36 AM
#6
TECH Apprentice
Thread Starter
iTrader: (3)
Join Date: Jul 2007
Location: Alma, Ga
Posts: 348
Likes: 0
Received 0 Likes
on
0 Posts
4/6 it isn't really that low in the back. It has spring clamps on the rear to help with the wheel hop. It pulls the back down a little. It sits about 1/4 higher in the back than the front with them removed,
Trending Topics
06-12-2009, 12:55 AM
#8
TECH Apprentice
Thread Starter
iTrader: (3)
Join Date: Jul 2007
Location: Alma, Ga
Posts: 348
Likes: 0
Received 0 Likes
on
0 Posts
They are chevy wheels. I see them on some of the crew cabs but they dont look that good on them cause they usually have big 4x4 looking tirer on them
