Pic of a HD belt tensioner?
Any one have a pic of the HD belt tensioner? I need to see what the mounting bracket for the Procharger/Roush type setup looks like (bolts to stock location). I haven't been able to find a good pic searching. Thanks!
|
there was someone selling one on here and it had pics
|
2 Attachment(s)
|
post #7 in this thread: https://www.performancetrucks.net/fo...d.php?t=464482
the back mounting section is sitting back by the balancer and the rest is still attached to the tensioner. Jed |
Originally Posted by Atomic
(Post 4550511)
Thanks |
That is the magnacharger HD tensioner. Call them (or any other maggie dealer) and they will sell you one.
|
That HD tensioner is basically the same as what I had on my Kenne Bell.
|
Originally Posted by Atomic
(Post 4551288)
That is the magnacharger HD tensioner. Call them (or any other maggie dealer) and they will sell you one.
KB if you need more pics of it off a vehicle or backside or something, pm me your number and ill text them to you! |
Thanks for the pics guys. What I'm really looking for is the mounting bracket that comes with Leftcoast32's HD tentioner kits for non maggie kits. You can text pics to 480-seven eight five-6132.
|
im looking to get this for my Roush TVS1900. I was quoted 400+shipping for the complete kit for a non maggie system
|
Originally Posted by kbracing96
(Post 4551391)
Thanks for the pics guys. What I'm really looking for is the mounting bracket that comes with Leftcoast32's HD tentioner kits for non maggie kits. You can text pics to 480-seven eight five-6132.
Jed |
Pat it looks beefier than the one with the original Kenne bell kit - is it the same one or is there a stronger spring? Please advise
Thanks |
I have 2 stock units if you need one let me know...free and you pay shipping
|
Sorry Kyle ive been super busy, i will text you some pics of my HD tensioner with leftcoast's bracket kit that i used to install .
It was a bit pricey but worth it as joe helped me install it over the phone and evrything fit great! |
I have a an idler or 2 laying around i can toss in too if you need them if it helps get you up and running.
|
I have a stock tensioner that's fine, just doesn't have enough travel to take up all the slake when the belt stretches in boost. I think I'm just gonna get the whole HD kit. :)
Thanks for the pics guys!! :D |
Subscribed.
|
Originally Posted by kbracing96
(Post 4551391)
Thanks for the pics guys. What I'm really looking for is the mounting bracket that comes with Leftcoast32's HD tentioner kits for non maggie kits. You can text pics to 480-seven eight five-6132.
|
Originally Posted by idahoblkss
(Post 4551692)
I JUST RECENTLY DID THIS CONVERSION ON MY PROCHARGER SETUP. sorry for the caps lol... and all i did is bought the brackets and hd tensioner and cut the far right pulley off of the bracket and it works perfect. i wont be home for a week or so , so i cant get a pic till then sorry.
|
pm sent
|
i wasnt aware that the hd tensioner wouldnt work on non maggie trucks.. damn guess thats more cost to factor in
|
1 Attachment(s)
|
Originally Posted by kbracing96
(Post 4558184)
Got what I needed today. Special thanks to my little buddy! ;)
http://i3.photobucket.com/albums/y57...6/photo-79.jpg |
The only thing I don't think I'll need is the water neck, but it comes in the sub assemble that the spacer next to it that you do need is in. So I guess you get it any way. :)
|
hmmmm, still using my stock tentioner with my roush... no probs yet... what kits do they have that i could use?
|
hey kb, where and how much did that set you back? pm me info if you can bud..thanks
|
3 Attachment(s)
I got it from Magnuson. The sub assembly part numbers are...
31-12-00-082 upgrade radix tensioner 65-12-57-031 tensioner bracket 31-12-02-032 water neck replacement SSR (I didn't use the neck, but I think that's the sub assm that the 2 bolt spacer comes in) Don't know that you lower boost guys really need this, but I'm pumping about 17psi out of this KB 2.8L :D Attachment 142472 Attachment 142473 Attachment 142474 |
did u fix the blower?
|
Originally Posted by charcold-bowtie
(Post 4558613)
did u fix the blower?
|
dang i need a 8 rib set up .... me like.. where did you get all of your 8 rib pulleys from and what did they run you?
|
Originally Posted by idahoblkss
(Post 4558646)
dang i need a 8 rib set up .... me like.. where did you get all of your 8 rib pulleys from and what did they run you?
|
Very nice. I plan to do the tensioner upgrade when I do my 8-rib swap instead of spending $105 on the IW tensioner pulley.
Originally Posted by kbracing96
(Post 4558703)
They came with the blower when I bought it all used. The crank pulley is an Innovators West 10% over driven, and the alt and PS pullies were from Pulley Boys.
|
Cory told me he got them from Pulley Boys and they don't look like IW's 8 rib stuff. Even the IW guy told me he didn't think they were his when I sent him a vid of a wobble issue I have with the crank pulley I'm not to happy with that they won't do anything about.
|
soooo what happened to the turbo setup?
|
Originally Posted by BlackGMC
(Post 4559490)
soooo what happened to the turbo setup?
|
Originally Posted by kbracing96
(Post 4558580)
I got it from Magnuson. The sub assembly part numbers are...
31-12-00-082 upgrade radix tensioner 65-12-57-031 tensioner bracket 31-12-02-032 water neck replacement SSR (I didn't use the neck, but I think that's the sub assm that the 2 bolt spacer comes in) Don't know that you lower boost guys really need this, but I'm pumping about 17psi out of this KB 2.8L :D http://i3.photobucket.com/albums/y57...6/photo-80.jpg http://i3.photobucket.com/albums/y57...6/photo-81.jpg http://i3.photobucket.com/albums/y57...6/photo-82.jpg |
Originally Posted by lablackbeast
(Post 4706696)
The pictures from this one looks way different, the tensioner is slanted all the way to the right/down mine is almost in the center and makes the belt hit the part of the tensioner
I think I see what your saying. I just posted these pics in your other thread. I think you problem is you need a shorter belt so the tensioner is clocked like mine in this pic, ;) |
Maggie tvs1900 4.8
Originally Posted by xx_ED_xx
(Post 4550483)
there was someone selling one on here and it had pics
|
The HD tensioner comes with an 8 rib pulley on it. Still works with a 6 rib belt though.
|
Ok that's way I wond er red thanks this should help with the belt slinging shouldn't it. Crank is pinned and everything
|
All times are GMT -5. The time now is 07:42 AM. |
© 2024 MH Sub I, LLC dba Internet Brands