PerformanceTrucks.net Forums
0 2015/10/18 16:28:26
Something to watch out for, and reason i flipped my sway bar!!!
Something to watch out for, and reason i flipped my sway bar!!!
0 2015/10/18 16:16:30
The fabtech links were a pain to cut off!!!
The fabtech links were a pain to cut off!!!
0 2015/10/18 16:14:33
Flipped my sway bar....
Flipped my sway bar....
0 2015/10/18 16:14:30
That better???
That better???
0 2015/10/18 16:12:34
0 2015/10/17 19:44:51
0 2015/10/17 17:00:44
This help??
This help??
0 2015/10/17 10:27:30
Cleaned up the band anchor and the plate thing that bolts ne tto the valve body.... Cant remember what its called (and now its bugging me)
Cleaned up the band anchor and the plate thing that bolts ne tto the valve body.... Cant remember what its called (and now its bugging me)
0 2015/10/16 18:49:12
New drain plug without that stupid ass rubber seal built in
New drain plug without that stupid ass rubber seal built in
0 2015/10/16 18:47:12
Trans pan cleaned up
Trans pan cleaned up
0 2015/10/16 18:47:08
New seal
New seal
0 2015/10/16 18:47:04
New bushing in place
New bushing in place
0 2015/10/16 18:47:00
0 2015/10/15 22:37:00
Got that PITA drain plug out after 2 hours.... Any sugestions on what style to put back in there???
Got that PITA drain plug out after 2 hours.... Any sugestions on what style to put back in there???
0 2015/10/15 22:36:59
More carnage in the bottom of the pan....
More carnage in the bottom of the pan....
0 2015/10/15 22:36:56
Caught pump bushing pulling seal...... Damnit!!!
Caught pump bushing pulling seal...... Damnit!!!
0 2015/10/15 22:36:52
Bw input sprag
Bw input sprag
0 2015/10/14 18:45:55
Manifold switch....
Manifold switch....
0 2015/10/14 18:45:46
Separator plate post rust removal....
Separator plate post rust removal....
0 2015/10/13 18:22:00
Pwm plug peened... Amazing what two taps with an 8oz ball peen will do to a 1/16" piece of aluminum... :rotflmao:
Pwm plug peened... Amazing what two taps with an 8oz ball peen will do to a 1/16" piece of aluminum... :rotflmao:
0 2015/10/13 18:21:26
Well after a 12:30am walmart run for a $15 set of drill bits..... My pwm feed hole is plugged, gonna see if i cant use a real hammer and a vise at work to peen it a bit flatter tomorrow...
Well after a 12:30am walmart run for a $15 set of drill bits..... My pwm feed hole is plugged, gonna see if i cant use a real hammer and a vise at work to peen it a bit flatter tomorrow...
0 2015/10/12 21:58:31
Separator plate marked and drilled......
Separator plate marked and drilled......
0 2015/10/11 22:53:09
1/8" hole drilled through valve body for the hd2-3 shift valve as per sonnax instructions.....
1/8" hole drilled through valve body for the hd2-3 shift valve as per sonnax instructions.....
0 2015/10/11 22:53:06
My handy dandy accumulator valve shim installation tool... Lost a set of feeler guages somewhere....
My handy dandy accumulator valve shim installation tool... Lost a set of feeler guages somewhere....
0 2015/10/09 19:24:48
Hd 2-3 valve goin in!!!
Hd 2-3 valve goin in!!!
0 2015/10/09 19:24:35
I missed some pics, apparently!! Piston goes in spring next then cover... Was running out of time at work... So busy tonight!!! :jest:
I missed some pics, apparently!! Piston goes in spring next then cover... Was running out of time at work... So busy tonight!!! :jest:
0 2015/10/09 19:24:27
Both balls in and staked...shitty stake job BTW!!!
Both balls in and staked...shitty stake job BTW!!!
0 2015/10/09 19:24:18
Pin pulled, piston out!!!
Pin pulled, piston out!!!
0 2015/10/09 19:24:13
Forward accumulator plate off
Forward accumulator plate off
0 2015/10/09 19:24:01
Accumulator valve shim... PITA!!!
Accumulator valve shim... PITA!!!
0 2015/10/09 19:23:46
New one goin in with spring
New one goin in with spring
0 2015/10/09 19:23:29
Piston installed, wave spring goes beneath it..
Piston installed, wave spring goes beneath it..
0 2015/10/09 19:07:06
Outer sonnax spring installed
Outer sonnax spring installed
0 2015/10/09 19:06:58
Inner sonnax spring installed
Inner sonnax spring installed
0 2015/10/09 19:06:54
And now for sonnax, balls in housing staked, half of my punches are broke waiting for snappy to get em replaced
And now for sonnax, balls in housing staked, half of my punches are broke waiting for snappy to get em replaced
0 2015/10/09 19:06:50
Painted servo cover... Aluminum paint, i really like that paint for accesory brackets etc
Painted servo cover... Aluminum paint, i really like that paint for accesory brackets etc
0 2015/10/09 19:06:46
Clip back on
Clip back on
0 2015/10/09 19:06:41
0 2015/10/09 19:06:38
Compressing spring housing into vette servo, used my ball joint press, to get snap ring back in
Compressing spring housing into vette servo, used my ball joint press, to get snap ring back in
0 2015/10/09 19:06:34