PerformanceTrucks.net Forums
0 2016/11/12 04:58:41
Even came with a tonneau cover
Even came with a tonneau cover
0 2016/11/12 04:56:48
0 2016/10/30 18:04:30
0 2016/10/30 18:04:25
0 2016/10/30 18:04:11
0 2016/10/30 18:03:50
Radio ac control dash bezel dash etc
Radio ac control dash bezel dash etc
0 2016/10/30 18:02:10
0 2016/10/30 18:01:48
0 2016/10/30 18:01:23
60 / 40 seats, steam clean and they would look brand new havent noticed any tears
60 / 40 seats, steam clean and they would look brand new havent noticed any tears
0 2016/10/30 18:00:15
93 gauge cluster
93 gauge cluster
0 2016/10/30 17:59:40
0 2016/08/09 11:30:12
0 2016/08/07 10:01:26
0 2016/08/07 10:01:08
0 2016/08/07 10:00:40
My 9 year old daughter caught this little guy spying on us working on the truck. Made her let him/her go lol
My 9 year old daughter caught this little guy spying on us working on the truck. Made her let him/her go lol
0 2016/05/16 10:02:29
Yoke engagement, im worried about this, not sure whats going on. Used dirty dingo motor mounts and transmission cross member bolted in stock loction. But drive shaft appears to have shrunk by 1 1/4 inches... were the 89 700r4s linger than 2001 4l60e ?
Yoke engagement, im worried about this, not sure whats going on. Used dirty dingo motor mounts and transmission cross member bolted in stock loction. But drive shaft appears to have shrunk by 1 1/4 inches... were the 89 700r4s linger than 2001 4l60e ?
0 2016/05/16 09:59:42
Cleaning up tranny cooler lines and getting the o2 sensor wires out of the way
Cleaning up tranny cooler lines and getting the o2 sensor wires out of the way
0 2016/05/16 09:58:16
Pieced together a m12x1.5 to 3/8 npt adapter. Not as elegant as a after market piece, cost me 15 dollars in fittings but its stainless, rated for ungodly PSI and with the swivel im able to clock it where ever i like
Pieced together a m12x1.5 to 3/8 npt adapter. Not as elegant as a after market piece, cost me 15 dollars in fittings but its stainless, rated for ungodly PSI and with the swivel im able to clock it where ever i like
0 2016/05/16 09:51:32
0 2016/05/15 12:31:46
0 2016/05/15 12:31:26
Friend who did my wiring got the old oil pressure gauge to work with the 2001 sending units. Not confident the gauge is accurate
Friend who did my wiring got the old oil pressure gauge to work with the 2001 sending units. Not confident the gauge is accurate
0 2016/05/13 04:49:35
Going to buy some rubber line clamps and hopefully mount them like this
Going to buy some rubber line clamps and hopefully mount them like this
0 2016/05/11 05:05:42
Routing lines for tranny cooler, 2 45 degree jic fittings onto parker 801 hose
Routing lines for tranny cooler, 2 45 degree jic fittings onto parker 801 hose
0 2016/05/11 05:04:39
Installed fuel pump
Installed fuel pump
0 2016/05/11 05:03:54
Accessories on except alternator, thought my small case 75 amp alt would fit but it wont without modifying the dirty dingo brackets. So need to buy a large case 105 amp alt. Also my ac lines appear to be to short despite the sanden 508 conversionplate from dirty dingo. Thats depressing. Bought the plate so i wouldnt have to have new lines made.
Accessories on except alternator, thought my small case 75 amp alt would fit but it wont without modifying the dirty dingo brackets. So need to buy a large case 105 amp alt. Also my ac lines appear to be to short despite the sanden 508 conversionplate from dirty dingo. Thats depressing. Bought the plate so i wouldnt have to have new lines made.
0 2016/05/03 17:27:33
Solution for shifter
Solution for shifter
0 2016/05/03 17:26:36
This is all the way forward on the dirty dingo mounts. Put the tranny right back in the same location but i might unbolt it tomorrow and slide it back further, ive only got 1 3/4 inch yoke engagement. My buddy pulled it so i dont know if thats how it was but makes me nervous. Id like at least 2.5 inches of engagement on the driveshaft yoke.
This is all the way forward on the dirty dingo mounts. Put the tranny right back in the same location but i might unbolt it tomorrow and slide it back further, ive only got 1 3/4 inch yoke engagement. My buddy pulled it so i dont know if thats how it was but makes me nervous. Id like at least 2.5 inches of engagement on the driveshaft yoke.
0 2016/04/30 17:43:06
0 2016/04/30 17:41:48
Home 3.5 hours later been to long since ive done this shouldnt take 7 hours
Home 3.5 hours later been to long since ive done this shouldnt take 7 hours
0 2016/04/30 17:40:36
Worlds best wife
Worlds best wife
0 2016/04/30 17:39:38
0 2016/04/30 17:38:51
3.5 hours later
3.5 hours later
0 2016/04/30 10:13:04
0 2016/04/30 10:12:36
All bolted up
All bolted up
0 2016/04/24 14:33:59
Dont know what to think about these pintel caps, wish i could remove them so the injectors would sit further down but if it doesnt leak ill be happy lol
Dont know what to think about these pintel caps, wish i could remove them so the injectors would sit further down but if it doesnt leak ill be happy lol
0 2016/04/24 14:31:35
0 2016/04/24 14:30:42
0 2016/04/24 14:30:08
Fuel rail spacers i Jimmy rigged
Fuel rail spacers i Jimmy rigged
0 2016/04/24 14:29:20
Dont try this at home lol. Long as we dont have an earthquake in the next week shes good. I pushed from all 4 sides and it didnt budge but id recommend leaving it on the stand. I needed it like this so i can reloom my harness the guy i paid did a horrible job and it lays out all weird
Dont try this at home lol. Long as we dont have an earthquake in the next week shes good. I pushed from all 4 sides and it didnt budge but id recommend leaving it on the stand. I needed it like this so i can reloom my harness the guy i paid did a horrible job and it lays out all weird
0 2016/04/20 19:13:21