PerformanceTrucks.net Forums
Balancer off
Balancer off
0 2016/02/21 02:09:09
Forgot i had a 3 bolt 4x cam gear....
Forgot i had a 3 bolt 4x cam gear....
0 2016/02/21 02:09:15
Valve covers and rockers out of the way
Valve covers and rockers out of the way
0 2016/02/21 02:09:19
0 2016/02/21 02:09:22
0 2016/02/21 02:09:28
Not any more they arent!!!!! At least not as soon as i can find a long enough bolt!!!!
Not any more they arent!!!!! At least not as soon as i can find a long enough bolt!!!!
0 2016/02/21 20:23:23
0 2016/02/22 00:03:30
0 2016/02/22 00:03:34
0 2016/02/22 00:03:38
0 2016/02/23 01:31:13
0 2016/02/23 01:31:17
0 2016/02/23 07:35:15
0 2016/02/23 07:35:22
Painted my balancer... Rust just doesnt do it for me!!!
Painted my balancer... Rust just doesnt do it for me!!!
0 2016/02/23 11:27:05
This is what happens when you mix dexcool with well water.... And forget to flush the system when the truck gets back to civilization....:bang:
This is what happens when you mix dexcool with well water.... And forget to flush the system when the truck gets back to civilization....:bang:
0 2016/02/23 11:27:11
These last two were right before the stud broke!!!!
These last two were right before the stud broke!!!!
0 2016/02/23 11:27:16
0 2016/02/23 11:27:22
Cam gear instaled an waiting on springs to be installed
Cam gear instaled an waiting on springs to be installed
0 2016/02/23 11:27:26
0 2016/02/23 16:32:24
Bank 2 done!!! Remind me next time to just pull the damn heads.... You better believe the 6.0 im building for the yukon will have the springs swapped on the bench before they go on the engine!!!! Hell if i was smart this would have been a swap springs onto the ither heads and swap heads..... Probably would have been quicker and less taxing mentally!!!
Bank 2 done!!! Remind me next time to just pull the damn heads.... You better believe the 6.0 im building for the yukon will have the springs swapped on the bench before they go on the engine!!!! Hell if i was smart this would have been a swap springs onto the ither heads and swap heads..... Probably would have been quicker and less taxing mentally!!!
0 2016/02/23 18:50:53
Bank 2 rockers in and torqued
Bank 2 rockers in and torqued
0 2016/02/23 20:40:05
Valve cover on for moment anyway
Valve cover on for moment anyway
0 2016/02/23 20:40:14
And bank 1 springsare done!!!! Why is it the last two damn springs went the way all of the rest didnt???
And bank 1 springsare done!!!! Why is it the last two damn springs went the way all of the rest didnt???
0 2016/02/23 20:40:22
Bank 1 rockers in....
Bank 1 rockers in....
0 2016/02/23 22:53:17
Coil packs
Coil packs
0 2016/02/23 22:53:23
0 2016/02/23 22:53:26
Timing cover installed
Timing cover installed
0 2016/02/23 22:53:29
The purple balancer adds 50 hp, if for no ither reason than.... ITS PURPLE!!!!!!! After looking at this pic i wish my block was painted aluminum too!!!
The purple balancer adds 50 hp, if for no ither reason than.... ITS PURPLE!!!!!!! After looking at this pic i wish my block was painted aluminum too!!!
0 2016/02/23 22:53:32
Saw no point in boring everyone with water pump on radiator in blah blah blah!!!!
Saw no point in boring everyone with water pump on radiator in blah blah blah!!!!
0 2016/02/24 18:43:37
This is the petcock hole in the old radiator.....
This is the petcock hole in the old radiator.....
0 2016/02/24 20:33:19
0 2016/02/28 06:01:21
0 2016/02/28 16:24:08
0 2016/02/28 16:24:12
0 2016/02/28 17:49:41
Non dod standard lifter on the left....dod on right
Non dod standard lifter on the left....dod on right
0 2016/02/29 08:29:44
0 2016/03/01 16:23:51
0 2016/03/01 16:23:59
Better shot of first page
Better shot of first page
0 2016/03/01 16:28:05
I ended up shaving the open end to an angle on both sides to clear the corners or the head on the front and rear springs andended up trimming the backside up and putting a notch in it to clear some of the points of my intake and injectors...
I ended up shaving the open end to an angle on both sides to clear the corners or the head on the front and rear springs andended up trimming the backside up and putting a notch in it to clear some of the points of my intake and injectors...
0 2016/03/01 21:05:52
Left
Left
0 2016/03/06 14:12:59