PerformanceTrucks.net Forums
Extra rear brackets....
Extra rear brackets....
0 2016/07/12 17:39:37
Exactly the damn same as the last set.....
Exactly the damn same as the last set.....
0 2016/07/12 17:39:34
At least i have an extra set of bushings now....
At least i have an extra set of bushings now....
0 2016/07/12 17:39:24
0 2016/07/12 17:38:58
Cleaned up hard oarts waiting to be reassembled...
Cleaned up hard oarts waiting to be reassembled...
0 2016/07/08 16:21:28
0 2016/07/08 16:21:15
All cleaned up and purty!!!
All cleaned up and purty!!!
0 2016/07/08 16:21:03
Stack of steels, retaining ring and snap rings waiting to be introduced to the parts washer.... Some of the steels i was able to reuse, mostly out of the 1-2-3-4/3-5-R drum(not the original one but the one i had)
Stack of steels, retaining ring and snap rings waiting to be introduced to the parts washer.... Some of the steels i was able to reuse, mostly out of the 1-2-3-4/3-5-R drum(not the original one but the one i had)
0 2016/07/08 16:20:55
1-2-3-4 piston
1-2-3-4 piston
1 2016/07/08 16:20:43
0 2016/07/08 16:20:29
Damage to the outer splines of the 4-5-6 hub...part of the reason i replaced it aside from the snap ring and dampener having blown out of them...
Damage to the outer splines of the 4-5-6 hub...part of the reason i replaced it aside from the snap ring and dampener having blown out of them...
0 2016/07/08 16:20:08
1-2-3-4/3-5-R drum, emptied...
1-2-3-4/3-5-R drum, emptied...
0 2016/07/08 16:19:57
0 2016/07/06 17:50:15
Thsi is how it should look, all in one piece!!!
Thsi is how it should look, all in one piece!!!
0 2016/07/06 17:50:12
This is an aftermarket version that you can see the lip if you look close enough
This is an aftermarket version that you can see the lip if you look close enough
0 2016/07/02 12:34:54
Theisbis the kent moore gm tool
Theisbis the kent moore gm tool
0 2016/07/02 12:34:53
0 2016/07/02 09:52:09
0 2016/07/02 09:52:02
Output came with new input/output shaft sensor harness
Output came with new input/output shaft sensor harness
0 2016/07/01 14:44:02
Solid ring gears
Solid ring gears
0 2016/07/01 14:43:59
New output shaft assembly, which is according to the paper in the box an updated design, the old one the ring gears were seperatable, these are built into the housing.....
New output shaft assembly, which is according to the paper in the box an updated design, the old one the ring gears were seperatable, these are built into the housing.....
0 2016/07/01 14:43:56
They are huge though!!!
They are huge though!!!
0 2016/06/29 10:57:10
Not completely black, but the face of the wheels are..... I miss the truck being pewter... Lol!!!
Not completely black, but the face of the wheels are..... I miss the truck being pewter... Lol!!!
0 2016/06/29 09:31:41
Valve body mounting....
Valve body mounting....
0 2016/06/28 16:49:04
Ls bellhousing in place
Ls bellhousing in place
0 2016/06/28 16:48:57
Went ahead and set the new 3-5-r in with the clutches.... The vise grips are the 1-2-3-4/3-5-r instaayion band tool!!
Went ahead and set the new 3-5-r in with the clutches.... The vise grips are the 1-2-3-4/3-5-r instaayion band tool!!
0 2016/06/28 16:48:52
Cebter support back in
Cebter support back in
0 2016/06/28 16:48:46
Everything going back in temporarily without clutches and sn output shaft
Everything going back in temporarily without clutches and sn output shaft
0 2016/06/28 16:48:41
No chewed up teeth on the planetary
No chewed up teeth on the planetary
0 2016/06/28 16:48:37
Likewise with the low/reverse
Likewise with the low/reverse
0 2016/06/28 16:48:33
2-6 clutches dont look too bad
2-6 clutches dont look too bad
0 2016/06/28 16:48:27
More of the 4-5-6 clutches
More of the 4-5-6 clutches
0 2016/06/28 16:48:21
4-5-6 hub came apart and the splines are chewed up from the stripped 4-5-6 clutches
4-5-6 hub came apart and the splines are chewed up from the stripped 4-5-6 clutches
0 2016/06/28 16:47:53
Output ring gear... All teeth intact!!
Output ring gear... All teeth intact!!
0 2016/06/28 16:44:43
The output planetary assembly
The output planetary assembly
0 2016/06/28 16:44:28
Center support which is also the 2-6 and low/reverse clutch housing...
Center support which is also the 2-6 and low/reverse clutch housing...
0 2016/06/28 16:44:00
Think these are 4-5-6 clutches...
Think these are 4-5-6 clutches...
0 2016/06/28 16:39:18
Snap ring from hell!!!!
Snap ring from hell!!!!
0 2016/06/28 16:37:53
0 2016/06/28 16:37:41
Slight bowing of the 3-5-r clutches!!!
Slight bowing of the 3-5-r clutches!!!
0 2016/06/28 16:30:21