PerformanceTrucks.net Forums
Blower after re assembly
Blower after re assembly
0 2016/09/19 15:40:24
Intercooler hose pressure pre IC and post both HEX
Intercooler hose pressure pre IC and post both HEX
0 2016/09/07 11:51:27
Complete removed TVS2300 jackshaft on the bench
Complete removed TVS2300 jackshaft on the bench
0 2016/09/07 11:46:56
Engine sand blower
Engine sand blower
0 2016/09/07 11:46:52
TVS2300 jackshaft IAT sensor wiring
TVS2300 jackshaft IAT sensor wiring
0 2016/09/07 11:46:49
TVS2300 jackshaft separated
TVS2300 jackshaft separated
0 2016/09/07 11:46:46
TVS2300 jackshaft ported lower manifold and phenolic spacer
TVS2300 jackshaft ported lower manifold and phenolic spacer
0 2016/09/07 11:46:43
TVS2300 jackshaft Intercooler
TVS2300 jackshaft Intercooler
0 2016/09/07 11:46:40
0 2016/09/07 11:46:37
Complete removed blower on the bench
Complete removed blower on the bench
0 2016/09/07 11:46:34
0 2016/06/20 13:02:17
0 2016/06/20 13:01:58
0 2016/06/20 13:01:41
Y An fitting in case I want to add a second pump later
Y An fitting in case I want to add a second pump later
0 2016/06/20 13:01:25
Closer look at the bulkhead
Closer look at the bulkhead
0 2016/06/20 13:01:09
Modified Bucket
Modified Bucket
0 2016/06/20 13:00:52
Finally... start of my Return fuel system
Finally... start of my Return fuel system
0 2016/06/15 09:43:29
Belt wrap with the 3.2" pulley. 100mm idler will make it even better... I still question whether it is enough to stop belt slip.
Belt wrap with the 3.2" pulley. 100mm idler will make it even better... I still question whether it is enough to stop belt slip.
0 2016/04/04 07:39:00
TPIS 102mm in comparison to a ported 90MM LS2 throttle body
TPIS 102mm in comparison to a ported 90MM LS2 throttle body
0 2016/02/02 13:15:09
10/31/15 time slip
10/31/15 time slip
0 2015/11/16 20:20:14
5" intake close up
5" intake close up
0 2015/11/04 06:20:04
5" intake complete
5" intake complete
0 2015/11/04 06:17:15
5" intake tube
5" intake tube
0 2015/11/02 06:25:32
0 2015/10/30 09:56:34
0 2015/10/19 07:36:04
0 2015/10/19 07:35:43
I'm back in the saddle again! - Aerosmith
I'm back in the saddle again! - Aerosmith
0 2015/10/13 07:47:26
Accessories at an angle
Accessories at an angle
0 2015/10/07 08:14:36
Accessories are on
Accessories are on
0 2015/10/07 08:12:44
Blower is on!
Blower is on!
0 2015/10/07 08:11:57
Engine is in!
Engine is in!
0 2015/10/07 08:10:35
notched torsion crossmember
notched torsion crossmember
0 2015/10/07 08:06:18
Stock LQ9 is out!
Stock LQ9 is out!
0 2015/10/05 09:05:01
Where'd my engine go?
Where'd my engine go?
0 2015/10/05 09:03:52
Final Mock up
Final Mock up
0 2015/10/05 09:03:07
Final paint on all covers
Final paint on all covers
0 2015/10/05 09:02:28
Intake port of lower manifold into the cylinder head port.
Intake port of lower manifold into the cylinder head port.
0 2015/10/01 11:32:29
Lower manifold intake ports sitting on cyl heads
Lower manifold intake ports sitting on cyl heads
0 2015/10/01 11:31:55
Long block with Lower manifold in place
Long block with Lower manifold in place
0 2015/10/01 11:31:28
Injector spacers to go with the Spacer... slightly too tall. Hopefully with the gasket they will work perfectly.
Injector spacers to go with the Spacer... slightly too tall. Hopefully with the gasket they will work perfectly.
0 2015/09/30 07:13:19