All Truck Shoot-Out in Memphis, TN!!
Dec 15, 2006 | 08:32 AM
#231
Teching In
Joined: Dec 2006
Posts: 29
Likes: 0
From: Columbus, Mississippi
Originally Posted by slowprocess
It's a 99 single cab 2x4. Weight is up alittle from stock ones due to the cage. No mudholes for me, though, mine would probably get stuck on the wet grass on the side of the road with the tires I have on it.
I don't think he can run that on bolt ons alone. It appeared that he ran a 13.8 on motor, which I can believe, but a 13.4 with that weight and just bolt ons is pretty far fetched IMO. Doesn't really matter if it can or can't though, cause this entire thread has been intended to get some grudge matches anyway.
I don't think he can run that on bolt ons alone. It appeared that he ran a 13.8 on motor, which I can believe, but a 13.4 with that weight and just bolt ons is pretty far fetched IMO. Doesn't really matter if it can or can't though, cause this entire thread has been intended to get some grudge matches anyway.
Mark
Dec 15, 2006 | 08:33 AM
#232
Thread Starter
TECH Resident
Joined: Jun 2005
Posts: 872
Likes: 0
From: O-G'ville, SC
Originally Posted by TurboGibbs
The trash talking is fine and all but how about a new thread for info only. 9 post of Memphis race info in the middle of 220 other post is confusing to say the least. 
Dec 15, 2006 | 08:40 AM
#233
Teching In
Joined: Dec 2006
Posts: 29
Likes: 0
From: Columbus, Mississippi
slowprocess, in my opinion he can get a 13.4 all motor. We are actually shooting for a 12.8 all motor. Keep in mind that he is a quad cab and he will be running slicks and 17" aluminum wheels instead of 20's on street tires weighing in at 5400lbs track prep. How much does your truck approximately weigh at track prep? He got a lil sumthin sumthin done to the truck since he ran that 13.9, but high 12's are coming. No doubt, you have a bad *** truck and I can't wait to see some of these grudge matches. This is all in fun anyway.
Mark
Mark
Dec 15, 2006 | 08:41 AM
#234
Originally Posted by marksdaleblvd
slowprocess, in my opinion he can get a 13.4 all motor. We are actually shooting for a 12.8 all motor. Keep in mind that he is a quad cab and he will be running slicks and 17" aluminum wheels instead of 20's on street tires. He got a lil sumthin sumthin done to the truck since he ran that 13.9. No doubt, you have a bad *** truck and I can't wait to see some of these grudge matches. This is all in fun anyway.
Mark
Mark
Dec 15, 2006 | 08:46 AM
#235
Teching In
Joined: Dec 2006
Posts: 29
Likes: 0
From: Columbus, Mississippi
Lots of fun. Where is Cleveland Mississippi at, I'm in Columbus MS. I still think I can get down to low 14's high 13's. I still have a comp 268 cam to put in along with beehive valve springs, an Edge 2800 Converter, Transgo shift kit, Roll Pan, and some 17's with slicks. Then I'll be happy with my times.
Mark
Mark
Dec 15, 2006 | 08:55 AM
#236
Originally Posted by marksdaleblvd
Lots of fun. Where is Cleveland Mississippi at, I'm in Columbus MS. I still think I can get down to low 14's high 13's. I still have a comp 268 cam to put in along with beehive valve springs, an Edge 2800 Converter, Transgo shift kit, Roll Pan, and some 17's with slicks. Then I'll be happy with my times.
Mark
Mark
Dec 15, 2006 | 09:14 AM
#237
Teching In
Joined: Dec 2006
Posts: 29
Likes: 0
From: Columbus, Mississippi
Originally Posted by slowprocess
We're about 3 hrs south of Memphis......just about dead center between Memphis and Jackson. Straight west of Grenada. I know you'd be happy with the times after those mods!
Mark
Dec 15, 2006 | 09:36 AM
#238
Originally Posted by marksdaleblvd
I am also 2 1/2 to 3 hours south of memphis. Are there any 1/4 mile tracks for us to run at around here?
Mark
Mark
We always go to Hattiesburg to get some good racing/timeslips down.
