02 Camaro SS, Modded
#1
11 Second Club
Thread Starter
iTrader: (13)
Join Date: Mar 2008
Location: Houston
Posts: 1,383
Likes: 0
Received 0 Likes
on
0 Posts
02 Camaro SS, Modded
I have over $20k in mods, not including the price of the car. The suspension and rear are already set up for big power so it would be fairly easy/cheap to turn it into a reliable 9 second car. Has about 93k miles. Paint has some scratches as you would expect from a 10 year old car but it's not too bad, has been garage kept for the last 6 years. Rear bumper has some paint damage from the rubber over the years.
Asking 16k firm.
Asking 16k firm.
#2
11 Second Club
Thread Starter
iTrader: (13)
Join Date: Mar 2008
Location: Houston
Posts: 1,383
Likes: 0
Received 0 Likes
on
0 Posts
Mods
Engine:
-QTP headers
-Dynomax bullet mufflers, currently just running bullets srtaight off the collectors
-FAST 90mm intake manifold
-FAST 90mm TB
-Custom 4" cold air intake
-ASP pulley
-Meziere electric water pump (street)
-AFX wideband (hidden display, for tuning only)
-Autometer wideband (for display, used on opposite bank of AFX while tuning to ensure accuracy)
-Lingenfelter 2-step
-Speed density tune
Fuel:
-Racetronix pump
-Hot wire kit
-6an braided stainless lines for supply and return
-Aeromotive regulator
-Black anodized aluminum rails
-Trickflow filter
-Spare Racetronix pump
Drivetrain:
-Pro 5.0 shifter
-Tick Performance adjustable master cylinder
-Tick remote speed bleeder
-Monster lvl. 3 clutch & flywheel
-PST alum. driveshaft
-Midwest Chassis fabricated 9"
-4.11 gear
-Strange aluminum center section
-Detroit locker
-35 spline Moser axles
-Backbrace
Suspension/Chassis:
-MWC tunnel mount torque arm
-MWC LCA's & relo. mounts
-MWC PHB
-MWC drag bar
-MWC crossmember with DSS loop
-Racecraft chromemoly K-member
-Spohn solid motor mounts
-Racecraft chromemoly upper & lower control arms
-Strange race brakes front & rear
-QA1r shocks w/300lb springs up front
-AFCO DA shocks w/275lb springs up front (brand new, yet to be installed)
-Stock rear springs and shocks
-Wolfe 6 point chromemoly roll bar
-UMI SFC's
Exterior:
-Shaved front bumper
-Black halos
-Black front turn signals & rear markers
-Graphite GS stripes
-Sunoco pin-on hood
-15X10 Prostars in rear w/ 325 Hoosier DR's (~50%)
-MT 10X28 Slicks for track (less than 5 passes on them)
-Greg Weld 15X3.5 front
Interior:
-New carpet (speed inc.)
-Complete stock sterio system w/ Infinity Kappa fronts
-Silver faced gauges and TA bezel
-Kirkey race seat
-5pt. harness for driver
-Black leather transam passenger seat
-No rear seats
-Wolfe 6 point roll bar (chromemoly)
Following parts are nib yet to be installed
-3 gauge pillar pod
-Autometer Cobalt wideband gauge
-Autometer Cobalt fuel pressure gauge
-Autometer Cobalt Digital Proshift Gauge
-Wolfe mini tubs
Engine:
-QTP headers
-Dynomax bullet mufflers, currently just running bullets srtaight off the collectors
-FAST 90mm intake manifold
-FAST 90mm TB
-Custom 4" cold air intake
-ASP pulley
-Meziere electric water pump (street)
-AFX wideband (hidden display, for tuning only)
-Autometer wideband (for display, used on opposite bank of AFX while tuning to ensure accuracy)
-Lingenfelter 2-step
-Speed density tune
Fuel:
-Racetronix pump
-Hot wire kit
-6an braided stainless lines for supply and return
-Aeromotive regulator
-Black anodized aluminum rails
-Trickflow filter
-Spare Racetronix pump
Drivetrain:
-Pro 5.0 shifter
-Tick Performance adjustable master cylinder
-Tick remote speed bleeder
-Monster lvl. 3 clutch & flywheel
-PST alum. driveshaft
-Midwest Chassis fabricated 9"
-4.11 gear
-Strange aluminum center section
-Detroit locker
-35 spline Moser axles
-Backbrace
Suspension/Chassis:
-MWC tunnel mount torque arm
-MWC LCA's & relo. mounts
-MWC PHB
-MWC drag bar
-MWC crossmember with DSS loop
-Racecraft chromemoly K-member
-Spohn solid motor mounts
-Racecraft chromemoly upper & lower control arms
-Strange race brakes front & rear
-QA1r shocks w/300lb springs up front
-AFCO DA shocks w/275lb springs up front (brand new, yet to be installed)
-Stock rear springs and shocks
-Wolfe 6 point chromemoly roll bar
-UMI SFC's
Exterior:
-Shaved front bumper
-Black halos
-Black front turn signals & rear markers
-Graphite GS stripes
-Sunoco pin-on hood
-15X10 Prostars in rear w/ 325 Hoosier DR's (~50%)
-MT 10X28 Slicks for track (less than 5 passes on them)
-Greg Weld 15X3.5 front
Interior:
-New carpet (speed inc.)
-Complete stock sterio system w/ Infinity Kappa fronts
-Silver faced gauges and TA bezel
-Kirkey race seat
-5pt. harness for driver
-Black leather transam passenger seat
-No rear seats
-Wolfe 6 point roll bar (chromemoly)
Following parts are nib yet to be installed
-3 gauge pillar pod
-Autometer Cobalt wideband gauge
-Autometer Cobalt fuel pressure gauge
-Autometer Cobalt Digital Proshift Gauge
-Wolfe mini tubs
Thread
Thread Starter
Forum
Replies
Last Post